|
Connect the Linksys PAP2 to your Internet/Broadband Connection
1. Phone 1 - Plug in your analog phone cord:
2. Ethernet Port - Use an Ethernet cable to connect your PAP2 to your router or modem:
3. Power connection - Connect the power to your PAP2:
Verify and Configure your IP Address
First we need to verify that your PAP2 will acquire an IP Address automatically if your network supports DHCP.
If your network uses a DHCP Server to assign IP Addresses to network devices, or if you are connecting the PAP2 to a home router such as a Linksys or Netgear router or a modem that supports DHCP/NAT, please do the following:
- Put a standard telephone into the “Phone 1” of your PAP2.
- Pick up the phone connected to “Phone 1” and enter “ * * * * “. You will hear a voice prompt saying “Configuration menu: Please enter option followed by a pound key, or hangup to exit”.
- Press the keys 1 0 1 # on your analog phone.
- Then press 1 # to enable DHCP.
- Then press 1 to save your configuration settings. Hang up the phone and wait 2 minutes.
Verify that the PAP2 has a valid IP Address
- Pick up the phone connected to “Phone 1” of the PAP2 and enter “ * * * * “. You will hear a voice prompt saying “Linksys configuration menu”.
- Press the keys 101# on your ananlog phone. The system will now read back the IP address of your PAP2. Please write it down.
If the IP is 0.0.0.0, your PAP2 does not have a valid IP Address. In this case you need to :
- Hang up the phone, unplug and re-plug you PAP2 power cord.
- Wait 2 minutes, and check the IP again.
- If you still get 0.0.0.0, there can be two reasons for this:
- Your DHCP server is not assigning an IP address to the PAP2 (in which case you should check with your network administrator for assistance).
- Your network does not have a DHCP server or you have purchased a Static IP Address for the PAP2 from your ISP.
Manually Assigning a Static IP Address
If you have obtained a static IP from your Internet Service Provider (ISP) and you have to configure your adaptor with the static IP settings, please follow the instructions below:
- You will first have to obtain the following information:
- IP Address
- Default Gateway Subnet Mask
- Pick up the phone and dial “ * * * * “. You will hear a voice prompt saying “Linksys configuration menu”.
- Press the keys 101# on your analog phone to access the Static IP configuration menu.
- Press 0# to disable DHCP, then press 1 to save the setting.
- Press 111# to access the IP Address Menu.
- Enter your IP Address followed by # (i.e. 192*168*113*71 # to represent 192.168.113.71). Press 1 to save the setting.
- Press 131# to access the Default Gateway Menu.
- Enter your Default Gateway (i.e. 192*168*113*71 # to represent 192.168.113.71). Press 1 to save the setting. Note: Gateway should be different from IP address.
- Press 121# to access the Subnet Mask Menu.
- Enter your Subnet Mask (i.e. 255*255*255*0 # to represent Subnet Mask 255.255.255.0). Press 1 to save setting.
To verify the configuration was correct, please pick up the telephone receiver on the phone connected to the ATA, and dial “ * * * * “ to enter the Linksys configuration menu, Dial 1 1 0 # to hear the adaptor read back the IP Address that you have configured. If the IP read out is not the same as what you have entered in, please repeat steps 1 through 10 once again to ensure the settings.
Configure the PAP2 to connect to Aglow Network (For Provisioning)
1. Open your configuration page using your web browser: http://xxx.xxx.xxx.xxx (your ip address) to display below.
2. Click on to “Admin Login” then “Switch to Advanced View” to display more detailed configuration page.
3. Click on the Provisioning menu.
4. In the text box marked Profile Rule enter the address provided: http://www.aglow.sg/cgi-bin/linksys-pap2?$MA
5. Click on “Save Settings” at the bottom of the screen.
6. Restart the Linksys box and wait for a couple of minutes for the provisioning to take effect. You should see the LED on “Phone 1” to light up.
7. At this point there’s no need to configure the PAP2 box manually.
Manually Setting the Account and Password
1. Linksys PAP2 can handle 2 accounts at the sametime, to setup 1 account. Click on Line 1.
2. Enter the following information required.
- SIP Proxy-Require: sip.aglow.sg
- SIP port: 5060
- Proxy: sip.aglow.sg
- Display Name: 3106XXXX
- UserID: 3106XXXX (number provided by Aglow)
- Password: provided by Aglow
- Use Auth ID: YES
- Auth ID: 3106XXXX
3. Look for “Preferred Codec” and set it to “G729a” and “Use Pref Codec Only” to “No”. 4. Make sure that the option on top Line Enable is set to “Yes”. Then click “Save settings”. Follow same steps to configure Line 2 if required.
Verify the Connection Status
To verify the status of the PAP2. Click on Info to view the Line 1 Status. If settings are properly configured. Registration State will display “Online”
|
